USB ISDN TA128
Quick Start Guide
This product is designed for the ISDN with Basic Rate Interface.
USB ISDN TA128
Installing the USB ISDN TA128
Connect your ISDN line to the ISDN S0 RJ-45 jack. Connect the USB
cable to the USB port and connect the other end to the PC. Refer to the
following figure.
For Windows 98:
1. Start Windows. After the opening banner, Windows will
tell you that the new device has been detected. You will
then see the following screen. Click “Next >”.
2
Quick Start Guide
2. In the next window, select “Search for the best driver for your
device” and click “Next >”.
3. Insert the installation CD into the CD-ROM drive and
check “CD-ROM drive” in the next window.
4. Continue through the Wizard, clicking the “Next >”
buttons. Windows will start copying files to your system.
You will see the following screen prompting for the path
of the Windows source files. Please specify a location.
Click “OK”. Then, click “Finish” in the next window to end
the installation.
3
USB ISDN TA128
5. If you are prompted to restart the computer after Windows
finishes installing the driver, press “Yes”.
For Windows Me:
1. Start Windows. After the opening banner, Windows will
tell you that the new device has been detected. Select
“Specify the location of the driver” and click “Next >”.
4
Quick Start Guide
2. In next window, select “Search for the best driver for your
device”. Insert the installation CD into the CD-ROM drive
and check “Removable Media”. Click the “Next >” button.
3. Continue through the Wizard, clicking “Next >” at the
following screens. Windows will start copying files to
your system. Then, click “Finish” in the following window.
4. If you are prompted to restart the computer after Windows
finishes installing the drivers, press “Yes”.
5
USB ISDN TA128
For Windows 2000:
1. Start Windows. After the opening banner, Windows will
tell you that the new device has been detected. Click
“Next>”.
2. In next window, select “Search for a suitable driver for my
device”. Click “Next>”.
3. Insert the installation CD into the CD-ROM drive, then in
the next window check “CD-ROM drives” and click “Next>”.
6
Quick Start Guide
4. Click “Next>” to install the driver. When the following
windows titled “Digital Signature Not Found” appear, press
“Yes” to continue the installation.
7
USB ISDN TA128
5. Press “Finish” to end the installation.
For Windows XP:
1. Start Windows. After the opening banner, Windows will
tell you that the new device has been detected. Select
“Install the software automatically”. Insert the installation CD
into the CD-ROM drive and click “Next >”.
2. When next window appears, press “Next >” to continue
the installation.
8
Quick Start Guide
3. Click “Continue Anyway” when the following “Hardware
Installation” windows appear.
9
USB ISDN TA128
4. Press “Finish” to end the installation.
ISDN Utility and Diagnostic Program
The ISDN Utility includes helpful programs for the USB ISDN
TA128, such as a diagnostic program, an uninstallation program,
and an on-line manual.
After Windows installs the driver of your USB ISDN TA128,
the ISDN Utility may be installed automatically. If the ISDN
Utility is not installed, you may install it from the installation
CD.
You are highly recommended to run the diagnostic program to
make sure the USB ISDN TA128, its drivers and the ISDN line
are all properly installed and connected. Please follow these
instructions:
1. Open the “Programs” folder on the “Start” menu and click
on the “ISDN Utility” program folder.
2. Click on the “Diagnostic Program” item to start the program.
3. In the “Own ISDN Number” box, type in the subscriber
number of your ISDN line.
10
Quick Start Guide
4. Press “Loopback Test” to begin the diagnostic procedure. It
will make a call from the B1 channel that returns through
the B2 channel. The D and B channels will be tested for
line integrity.
Uninstalling the USB ISDN TA128
If you decide to permanently remove the driver and utility of the
USB ISDN TA128 from your system, you must run the
uninstallation program from the ISDN Utility program group as
follows:
1. Click “Start”, “Programs” and click the “ISDN Utility” item.
2. Click the “Uninstall DRV & UTL” item. The following ISDN
Uninstallation Program window opens.
3. Check the items that you want to completely remove from
the Windows system and click “OK”.
11
|
Black Box Computer Accessories 26640 User Manual
Bosch Power Tools Planer GHO 31 82 User Manual
Braun Styling Iron C 100 TS User Manual
Broan Ventilation Hood 619004EX User Manual
Brother Garage Door Opener PT 1090 User Manual
Bushnell Telescope 78 9470 User Manual
Camco Refrigerator 350A4502P296 User Manual
Campbell Hausfeld Welder WF2058 User Manual
Chamberlain Door 655501 User Manual
Chromalox Electric Heater PD438 2 User Manual