Canon Camera Lens EF M 55 200 IS STM User Manual

CT1-8598-000  
2. Zooming  
Handling Cautions  
ENG  
EF-M LENS Instructions  
Turn the lens’ zoom ring to adjust the size of the photo field or  
If the lens is taken from a cold environment into a warm  
one, condensation may develop on the lens surface and  
internal parts. To prevent condensation in this case, first  
put the lens into an airtight plastic bag before taking it from a  
cold to warm environment. Then take out the lens after it has  
warmed gradually. Do the same when taking the lens from a  
warm environment into a cold one.  
subject. (fig.)  
EF-M55-200mm f/4.5-6.3 IS STM  
For wider shots, turn the zoom ring toward the wide end.  
For closer shots, turn the zoom ring toward the telephoto end.  
Be sure to finish zooming before focusing. Zooming after  
focusing can affect the focus.  
Blurring may temporarily occur if the zoom ring is quickly  
rotated.  
Zooming during still image exposure will result in delayed  
focus. This causes any streaks of light that are captured  
during exposure to be blurred.  
Do not leave the lens in excessive heat such as in a car in  
direct sunlight. High temperatures can cause the lens to  
malfunction.  
Please also refer to the handling cautions found in your  
camera’s instructions.  
3. Manual Focus  
When the camera’s focus mode is set to [MF], focus manually by  
turning the focusing ring (fig.).  
Conventions used in this instruction  
Warning to prevent lens or camera malfunction or  
damage.  
Quickly rotating the focusing ring may result in delayed focus.  
Supplementary notes on using the lens and taking  
pictures.  
Focus mode is set using the camera. Please refer to the  
camera’s instructions.  
Aautofocusing in [AF+MF] mode, focus manually by  
pring the shutter button halfway and turning the focusing  
null-time manual focusing).  
This device complies with Part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
Do not make any changes or modifications to the equipment unles
otherwise specified in the instructions. If such changes or mod
should be made, you could be required to stop operation of the  
equipment.  
This equipment has been tested and found to comlimits
a class B digital device, pursuant to part 15 of the hese  
limits are designed to provide reasonable protectiul  
interference in a residential installatiTquipuses  
and can radiate radio frequency engy and, if not ined  
in accordance with the instructionsay cause harmfunce to  
radio communications.  
Nomenclature  
Focusing ring  
Hood mount  
Filter Mounting Thread  
Lens mount index  
Contacts  
Zoom position index  
Zoom ring  
. Image tabilizer  
his lens is uipped with an Image Stabilizer. This function  
corrects camera shake, allowing users to capture sharp images.  
Also, the Image Stabilizer automatically provides optimal image  
stabilization depending on shooting conditions (such as shooting  
still subjects and following shots). Please set the Image Stabilizer  
ON or OFF using the camera settings. See your camera’s  
instructions for details.  
Wide end  
Thank you for purchasing a Canon product.  
The Canon EF-M55-200mm f/4.5-6.3 IS STM lens is a  
telephoto zoom lens developed for digital cameras compatible  
with EF-M lenses*.  
The Image Stabilizer cannot compensate for a blurred shot  
caused by a subject that moved.  
However, there is no guarantee that iference l not occur in a  
particular installation. If this equipment caharmful interference  
to radio or television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Telephoto end  
Zoom ring  
The Image Stabilizer may not be fully effective if you shoot  
from a violently shaking vehicle or other transportation.  
The Image Stabilizer consumes more power than normal  
shooting, resulting in fewer shots and a shorter movie  
shooting time.  
* Only the following cameras are compatible with EF-M lenses (as  
of February 2014):  
Reorient or relocate the receiving antenna.  
EOS M, EOS M2*1  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
*1: Not available in certain countries and regions.  
"IS" stands for Image Stabilizer.  
"STM" stands for stepping motor.  
When shooting a still subject, it compensates for camera  
shake in all directions.  
It compensates for vertical camera shake during following  
shots in a horizontal direction, and compensates for  
horizontal camera shake during following shots in a vertical  
direction.  
When you use a tripod, the Image Stabilizer should be  
turned off to save battery power.  
Even with a monopod, the Image Stabilizer will be as  
effective as during hand-held shooting.  
Consult the dealer or an experienced radio/TV technician for help.  
CAN ICES-3 (B) / NMB-3 (B)  
Safety Precautions  
1. Mounting and Detaching the Lens  
See your camera’s instructions for details on mounting and  
detaching the lens.  
Do not look at the sun or a bright light source through the  
lens. Doing so could result in vision loss or blindness.  
Whether it is attached to the camera or not, do not leave  
the lens under the sun without the lens cap attached. This  
is to prevent the lens from concentrating the sun’s rays, which  
could cause a fire.  
After detaching the lens, place the lens with the rear end  
up to prevent the lens surface and contacts from getting  
scratched. (fig.)  
If the contacts get soiled, scratched, or have fingerprints on  
them, corrosion or faulty connections can result. The camera  
and lens may not operate properly.  
However, depending on the shooting environment, the  
Image Stabilizer effect may be less effective.  
If the contacts get soiled or have fingerprints on them, clean  
them with a soft cloth.  
If you remove the lens, cover it with the dust cap. To attach  
it properly, align the lens mount index and the index of the  
dust cap as shown in the diagram, and turn clockwise. (fig.)  
To remove it, reverse the order.  
ENG-1  
 

Belkin Switch P74242 D User Manual
Black Decker Mixer GM100 User Manual
Boca Research Printer FSP 42 User Manual
Boss Audio Systems Car Stereo System BV8963 User Manual
Bradford White Corp Water Heater 544 B User Manual
Bradford White Corp Water Heater EFR160T120 User Manual
Bravetti Mixer EP552HA User Manual
Casio Blood Pressure Monitor BP 1MY 1 User Manual
Casio Projector XJ A130V XJ A135V User Manual
Century Cooktop HES80 User Manual